Hammerhead By Polaris

(07/08) Hammerhead Oil Seal (19.8x30x5)

19.8 x 30 x 5 Oil SealOIL SEAL 19.8X30X5The GY6 150cc motor uses a total of two 19.8x30x5 oil seals - one at each end of the crankshaft.Hammerhead part # M150-1003110Hammerhead part #...

(06) Hammerhead O-Ring (6x1.8) for 150cc, GY6

6 x 1.8 O-ringM6x1.8 O-ring O-RING-THROTTLE BODY,2X27Hammerhead part # 14285

(05) Hammerhead O-Ring (107x2) for 150cc, GY6

m107 x 2 O-ring for small left cover, part # 14283, on crankcase for F/N/R 150ccHammerhead part # 14284Polaris part # 3050023 O-RING 107X2

(04) Cover

Small cover behind the variator on 150cc engines with F/N/R.  The o-ring for this part is part #14284.  This is only for the motors with F/N/R.This part is associated with the left-side...

(03) Hammerhead Crankcase Gasket for 150cc, GY6

Crankcase gasket for 150cc, this gasket is only used when the case is split apartGasket - CrankcaseHammerhead part # m150-1003014Carter Brothers part # 513-1025 / 5131025American SportWorks part #...

(03) Hammerhead Chain, Oil Pump Chain for 150cc, GY6

150cc Oil Pump Chain with 22 LinksChain-oil pumpHammerhead part # m150-1021000American Sportworks part # 14357Polaris part # 3050072 part # BN157QMJ-1400003

(02) Hammerhead Sprocket, 23T Oil Pump Sprocket / Oil Pump Gear for 150cc, GY6

Oil Pump Drive Sprocket for GY6 motors. This part is commonly found on GY6 150cc buggies in the Oil Pump Assembly section of the owner's manual. This item is used as the sprocket that goes with the...

(01) Hammerhead Oil Pump Assembly for 150cc, GY6

150cc oil pump assembly Bolt Hole Spacing: 33.3mm Outer Diameter: 46.5mm Hammerhead part # m150-1022000Old TJ Power Sports #  7.190.009, 12.021.013 Baja Part # BR150S-470Baja...

(06) Hammerhead Piston Ring Set for 150cc, GY6

OEM Piston Ring set for 150cc GY6 4-stroke QMI157 / QMJ157 engines Thin Ring Thickness: 0.4mm Thin Ring Width: 1.8mm Middle Oil Ring Thickness: 1.8mm Piston Ring Inner Diameter : 56mm Hammerhead...

(05) Hammerhead Piston Pin Clip for 150cc, GY6

***SOLD INDIVIDUALLY***Hammerhead part # M150-1004003Trailmaster part #  152.01.307Carter Brothers Part # 515-1035American Landmaster Part # 14345

(04) Hammerhead Piston Pin for 150cc, GY6

Hammerhead OEM 150cc Piston Wrist Pin Hammerhead part # M150-1004006American Landmaster part # 14346Trailmaster part # 157.01.306

(03) Hammerhead Piston for 150cc, GY6

Hammerhead OEM 150cc Piston, 57.4mmHammerhead part # M150-1004001American Landmaster part # 14347Trailmaster part # 157.01.301

(02) Hammerhead Key, M4x14 Woodruff Key for 150cc, GY6

This the stock crankshaft woodruff key for 125 and 150cc GY6 engines used in many buggies, ATVs, and scooters. WOODRUFF KEY 4X14 Hammerhead part # m150-1004002Hammerhead part # m150-1004005Polaris...

(01) Hammerhead Crankshaft and Conrad Assembly for 150cc with F/N/R

150cc Crankshaft Assy for 150cc vehicles with Neutral Position.  This works for vehicles with an internal revese ONLY.For 150cc vehicles WITHOUT a neutral position or WITH an external reverse...

(1)-Hammerhead Seat Back Cushion, Seat Back for GTS 150 / Platinum GTS 150 - 13-0401-01

GTS150 back portion of seat ONLY with logo engraved in seat.  This is the back portion of the seat with the Hammerhead logo embedded into it.  This seat back can retro fit into any...

(2)-Hammerhead Seat Cushion, Right (Passenger) Seat Bottom for GTS 150 / Platinum GTS 150 - 13-0401-01R

GTS150 bottom portion of seat ONLY for passenger (RIGHT) side.  This is the bottom portion of the seat that is the fixed seat and is not adjustable.  This seat bottom can retro fit into any...

(3)-Hammerhead Seat Cushion, Left (Driver) Seat Bottom for GTS 150 / Platinum GTS 150 - 13-0401-01L

GTS150 bottom portion of seat ONLY for driver (LEFT) side.  This is the bottom portion of the seat that comes with slides so it is adjustable.  This seat bottom can retro fit into any...

(4)-Hammerhead Bolt, M8x40 Special "T" Seat Rail Bolt - 9.900.840

Seat Rail Bolt, Bolt Sharp M8 x 1.25 x 40SCR-M8X1.25X40,DAC (H7510011) M8 X 1.25 X 40 "T" STYLE DACHammerhead Part # 9.900.840Trailmaster part # 57870804012505, 9.108.045American Landmaster...

(5)-Hammerhead Seat Rail Set for 150cc / 250cc / 300cc 6.000.057

Seat Rail Set for 150cc, 250cc, 300cc gokarts.  This set comes with both rails, including the one with the grab handle.  Hammerhead part # 6.000.057Hammerhead part # 6.000...

(6)-Hammerhead Nut, M8 Locking Flange Nut - 9.220.008

m8 Locking Flange Nut Size: M8 (Metric 8mm diameter center opening) Height: ~7mm Thread Pitch: 1.25mm Price is per piece Hammerhead Part # 9.220.008Hammerhead Part # 6.034.096Hammerhead Part # 7...

(7)-Hammerhead Racing Seat Belt, 5-Point with Metal Latch and Link for Platinum GTS 150 - 6.000.354-P

Racing-style 5-point safety harness system with a metal latch and link clasp.  This seat belt is used on the Platinum GTS150, but can interchange with any 5-point seat belt assembly...

(7)-Hammerhead Seat Belt Assembly 5-Point - 6.000.354

Five-Point Safety Harness Seat Belt for GT250, GT150, GTS250 or GTS150 Hammerhead Go-Kart or any kart that uses a Five-Point Seat belt. Seat Belt - Complete Includes Both Driver and Passenger...

(8)-Hammerhead Bolt, M7/16"x28 Special Bolt - 9.700.001

m7/16x28 Special Bolt for SeatbeltHammerhead Part # 9.700.001 

(9)-Hammerhead Washer, 7/16 Washer - 9.700.002

Washer 7/16 Hammerhead Part # 9.700.002 American Sportworks Part # 14289Baja Reaction 150 (2-seater model) Part # BR150S-187Baja Reaction 250 Part # BR150S-221Baja Dune 150 Part #...

(10)-Hammerhead Washer, 7/16 Lock Washer - 9.700.005

Lock Washer 7/16Used with seat belt hardware Hammerhead part # 9.700.005

(11)-Hammerhead Nut, 7/16 Nut - 9.700.003

Belt Nut M7/16 for SeatbeltHammerhead Part # 9.700.003

(12/04)-Hammerhead Bolt - M8x40 Flange Bolt - 9.108.040

M8x1.25x40 bolt.  M8 x 1.25 x 40 bolt Size: M8 (Metric 8mm diameter) Length: 40mm Thread Pitch: 1.25mm Type: Hex Washer Head Price is per bolt Hammerhead part # 9.108.040Hammerhead part # 9...

(01)-Hammerhead Bolt, M6x16 Flange Bolt - 9.106.016

150cc starter motor bolt m6x16bolt flange m6x16 Size: M6 (Metric 6mm diameter) Length: 16mm Thread Pitch: 1mm Price is per bolt m6x16 Flange BoltCommonly used for 150cc starter motorHammerhead part...

(02/05)-Hammerhead Nut, M6 Locking Flange Nut - 9.220.006

M6 Locking Flange Nut Size: M6 (Metric 6mm diameter center opening) Height: ~7mm Thread Pitch: 1mm Price is per piece Hammerhead Part # 9.220.006 Hammerhead Part # 9.210.006 Hammerhead...

(3)-Hammerhead Fender, 17" x 7.5" Three Bolt Holes Fender for Mudhead 208R / 150cc / 250cc / 300cc - 7.010.034-SS replaces 15206, 7.010.034, 17-0211-00

These fenders are used on all four wheels for the MudHead and used as front fenders on other 150cc and 250cc go-karts 7.5" wide and 17" long This is the fender for Mudhead / 208R for all...

(4)-Hammerhead Fender Bracket Double-Bolt Strut Mount, Silver, Front Right (Passenger) for 150cc / 250cc / 300cc - 13-0625-01R

This bracket has a TWO bolt mount to strut.  This is the bracket that is used on all 2017 GTS models and newer.  For Single Bolt mount to strut, please use part # 6.000.102-SRight /...

(5)-Hammerhead Hood, Front Upper Nose Piece for GTS 150 / Platinum GTS 150 - 13-0201-00

GTS 150 front plastic hood. This is the upper hood / upper nose piece for the GTS150 only and does NOT include lower panel (part # 13-0202-03). ***HOODS MAY COME WITH DIFFERENT STICKERS THAN WHAT IS...

(6)-Hammerhead Hood, Lower Plastic Black Hood for GTS 150 / Platinum GTS 150 - 13-0203-03-FB

The lower black part of the GTS hood that mounts to the bottom side of the upper hood (13-0201-00).Hammerhead Part # 13-0202-03-FBHammerhead Part # 13-0202-03 

(7)-Hammerhead Bolt, M6x15 Phillips Head Bolt - 003-060015-00

m6 x 15 Large Head Phillips Screw Size: M6 (Metric 6mm diameter) Length: 15mm Thread Pitch:  Type: Phillips Head Price is per bolt Hammerhead part # 003-060015-00Hammerhead part # 9.600...

(8)-Hammerhead Fender, Two Bolt Holes, Rear Right (Passenger) Colored Fender for GTS 150 / Platinum GTS 150 - 13-0204-00R

Rear, passenger-side (RIGHT) fender for GTS-style karts.PLEASE SELECT THE COLOR OPTION IN THE DROP DOWN MENU BELOW.Hammerhead Part # 13-0204-00RHammerhead part # 13-0204-00R-SLV...

(9)-Hammerhead Bolt, M6x14 Flange Bolt - 9.106.014

m6 x 14 bolt, fender bolts.  Bolts that hold fender on to bracket Size: M6 (Metric 6mm diameter) Length: 14mm Thread Pitch: 1mm Price is per bolt Hammerhead part # 9.106...

(10)-Hammerhead Fender Bracket Two-Bolt Mount, Rear Right (Passenger) for GTS 150 - 13-0601-01R

Right / Passenger Side Rear Fender Bracket for GTS 150s.  This is a two-bolt mount to the frame bracket that is used on all 2017 GTS models and newer.  For previous GTS models and older...

(11)-Hammerhead Fender Bracket Two-Bolt Mount, Rear Left (Driver) for GTS 150 - 13-0601-01L

Left / Driver Side Rear Fender Bracket for GTS 150s.  This is a two-bolt mount to the frame bracket that is used on all 2017 GTS models and newer.  For previous GTS models and older with a...

(12)-Hammerhead Fender, Two Bolt Holes, Rear Left (Driver) Colored Fender for GTS 150 / Platinum GTS 150 - 13-0204-00L

Rear, driver-side (LEFT) fender for GTS karts.  PLEASE SELECT THE COLOR OPTION IN THE DROP DOWN MENU BELOW.Hammerhead Part # 13-0204-00LHammerhead part # 13-0204-00L-SLV...

(13)-Hammerhead Fender Bracket Double-Bolt Strut Mount, Silver, Front Left (Driver) for 150cc / 250cc / 300cc - 13-0625-01L

This bracket has a TWO bolt mount to strut.  This is the bracket that is used on all 2017 GTS models and newer.  For Single Bolt mount to strut, please use part # 6.000.067-SLeft / Driver...

(14/03)-Hammerhead Bolt - M5x16 Pan Screw - 003-050016-00

m5 x 16 pan screw Size: M5 (Metric 5mm diameter) Length: 16mm Type: Pan-head, Tapping screw Price is per bolt Hammerhead part # 003-050016-00Hammerhead part # 9.805.003American Landmaster part...

(01)-Hammerhead Clutch Variator, Front Driver Pulley for 150cc, GY6 - M150-1071000

Driven pulley used on all 150cc engines / 150cc stock variatorPulley includes:  outer face of pulley (fan), inner face of pulley (fixed), movable sheave & 6 roller weights ASM-DRIVING...

(2)-Hammerhead Clutch Bell, Clutch Drum / Housing for 150cc, GY6 - M150-1032000

Outter driven clutch drum for the 150cc clutch.   Outter 150cc clutch bellM150-1032000 Driven Disc CompHammerhead Part # M150-1032000American Sportworks Part # 14362 Carter Brothers...

(3)-Hammerhead Clutch Rear Pulley, Driven for 150cc, GY6 - M150-1031000

150cc clutch assembly does NOT come with outer drum (part # M150-1032000)  Clutch measurements:Clutch OD: 122mmBell ID: 125mm  DRIVEN PULLEY COMPAssembly includes the pulley and...

(04)-Hammerhead Drive Belt, 743x20x30 Belt for 150cc, GY6 - M150-1033000

Hammerhead 150cc drive belt, series 743 20 30. 743-20-30 CVT belt.  This is a Gates PowerLink 743-20-30 CVT high-quality OEM belt.Works with 125cc-150cc 4-stroke GY6 scooter engines. Also...

(05)-Hammerhead Clutch Roller for 150cc, GY6 - M150-1071002

Hammerhead 150cc Stock Clutch Roller.  Six rollers are used in the 150cc Variator / 150cc Front Clutch, Part # M150-1071000***SOLD INDIVIDUALLY******Price is per 1 roller, 6 rollers does 1...

(06/09)-M150-1004008 M150-1004008, NUT M12**SPECIAL ORDER**

(6)-M150-1004008 M150-1004008, NUT M12**SPECIAL ORDER**

(07)-M150-1040005 M150-1040005, WASHER o12**SPECIAL ORDER**

(7)-M150-1040005 M150-1040005, WASHER o12**SPECIAL ORDER**

(08)-M150-1040007 M150-1040007, NUT COMPRESSOR FLANGE M12**SPECIAL ORDER**

(8)-M150-1040007 M150-1040007, NUT COMPRESSOR FLANGE M12**SPECIAL ORDER**

(09)-Hammerhead Washer, 15.2×29×4 Clutch Washer - 157F.11.502

15.2×29×4 Washer b/w Clutch and Engine for 150ccHammerhead part # 157F.11.502

(10)-Hammerhead Washer, 15.2×29×7.5 Clutch Washer - 157F.11.501

15.2×29×7.5 Washer b/w Clutch and Nut before Belt CoverHammerhead part # 157F.11.501

(01)-Hammerhead Cylinder 150cc, GY6 - M150-1002200

150cc GY6 Cylinder (Sleeve is approximately 2.44" OD.)  57mm Cylinder Head for 150cc GY6 4-stroke QMJ157 engines. Overall Height: 60mm Bore Diameter: 57mm Intake Port Diameter:...